TJK Machinery (Tianjin) Co, Ltd
Installation And Connection of Reinforcing Cage
I WANT TO BUY PRODUCTS

Installation And Connection of Reinforcing Cage Installation And Connection of Reinforcing Cage

Reinforcing cage welder uses 100t crane platform to hoisting. Because the size and weight of the cage are quite large, the deformation of hoisting and shifting must be taken into account when making the cage. In order to protect the steel cage from deformation, two-point hoisting should be adopted. The first lifting point is located in the lower part of the skeleton, and the second lifting point is located between the midpoint of the skeleton length and the upper third point. When lifting, the first lifting point is raised first to lift up the skeleton, and then the second lifting point is hoisted at the same time. With the second lifting point is raising, the first lifting point is gradually relaxed until the skeleton is perpendicular to the platform, and the first lifting point is then released.

When hoisting the reinforcing cage into the hole, it should be aligned at the hole, put into the hole slowly. After the reinforcing cage enters the hole, it should be carried down slowly. In case of the resistance, it should stop devolving, identify the cause and deal with it before continuing. It is strictly prohibited to rise and fall, bump and force down.

When the reinforcing cage in the upper section is lowered to the top of the platform, which is about 1.5 m above the top of the platform, use 4 20t gourd to fix the reinforcement on the frame, then hang the next section of reinforcement to the top of the hole, so that main reinforcement of the upper and the lower two reinforcing cages align, and ensure that the upper and lower axes are consistent (fine-tuned with the gourd), at the same time, use the alignment of the upper and lower sections of the reinforcing, weld the sound measuring pipe and make straight line connection, after all the joints are connected, wind the screw bars, hoist up the reinforcing cage, take off the 4 hand pull gourds, then  descend into the hole slowly and uniformly, at the same time shun upper protective layer block of the reinforcement.

Spreading of acoustic tube adopts thread connection mode, the spreading of the pipe should be kept water free, at the same time, the pipe end of the acoustic tube should be covered with 6m thick plate, so as to prevent the reinforcing cage in the acoustic measuring pipe, such as sand, garbage, etc., from entering into the hole, and according to the design requirements to check the elevation, burying parts, etc. It should make a good record. After meeting the requirements, connect 8 main tendons to the upper end of the cage and extend them to the orifice,  prevent the reinforcing cage from being lifted up when its weight falls or the concrete is injected into the pile, the concrete of the pile body is poured out.

Related News
  • TJK Machinery Shows its Talent in OBAOR

    TJK Machinery Shows its Talent in OBAOR

    September 1, 2017Malaysia has become the preferred place for Chinese enterprises to "go out" in Southeast Asia. With the overall strategy for the development of the national "One Belt And One Road", and the central go...view
  • truss girder welding machine

    truss girder welding machine

    May 25, 20191. According to the specific conditions of the truss, first of all, it should be decomposed into several parts as far as possible and processed and welded in the inner field by truss girder welding ma...view
  • Standard Wire Bending Machine

    Standard Wire Bending Machine

    November 21, 2018Main Test Steps:1. The section which from 200mm to 250mm is checked on the metal wire to be calibrated and the surface of the wire must not be damaged when straightening.2. The radius of the clip is R...view
  • What Parts of the Rebar Cutting Machine Should Be Carefully Maintained to Prevent Rust?

    What Parts of the Rebar Cutting Machine Should Be Carefully Maintained to Prevent Rust?

    March 20, 2019At present, there are a lot of unreliable rebar cutting equipments on the market, so we must choose the regular manufacturers to buy machines. In this way, we can not only obtain high-quality and high...view
  • Main Test Steps of Standard Wire Bending Machine

    Main Test Steps of Standard Wire Bending Machine

    November 24, 2018Main Test Steps:1. The section which from 200mm to 250mm is checked on the metal wire to be calibrated and the surface of the wire must not be damaged when straightening.2. The radius of the clip is R...view
  • The Performance of Wire Mesh Welding Line Machine

    The Performance of Wire Mesh Welding Line Machine

    July 9, 2019We know how important the quality of the wire mesh is in the wire mesh welding line machine performance configuration, and brand price is next, and use value is the key. So how do you see the configur...view
  • TEL:+86 22-26907986
  • FAX:+86 22-26997888
  • EMAIL:tjksales@tjkmachinery.com
  • ADDRESS:Wuwei Rd., Lulugang Logistics Industrial Park, Tianjin, China
online