TJK Machinery (Tianjin) Co, Ltd
Common Faults and Solutions of Wire Mesh Welding Line Machine
I WANT TO BUY PRODUCTS
News

Common Faults and Solutions of Wire Mesh Welding Line Machine Common Faults and Solutions of Wire Mesh Welding Line Machine

Common fault treatment of wire mesh welding line machine: Screen black screen: first check whether there is power supply, power fuse, and whether the circuit between the screen and the main circuit board is connected. Disordered display: restart electrical cabinet, or welding machine sensor contact bad. Leakage welding of mesh: sensor damage; Control welding button damage; Short circuit of control line from controller to grid machine; Data input error; One or several leakage welding first check welding column head, connecting wire, brass square seat, and polish off the column head; Properly increase welding head pressure and welding current; Weak welding: oil pollution, wire drawing powder, oxide layer, etc.

Poor contact of welding loop; Small power supply welding transformer; The induction position of the wire mesh machine is wrong; Short welding time; The pressure spring of welding spot is damaged; Adjustment method of sensor for wire mesh welding line machine: 1. When the upper beam moves upward, drive the upper welding head upward. When the upper welding head leaves the mesh about 10mm, the upper edge of the upper beam starts to trigger the mesh sensor (that is, the upper edge of the upper beam and the lower edge of the mesh sensor circle are flush). 2. When the upper beam moves downward, drive the upper welding head downward, and when the upper beam reaches the lowest point (i.e. the maximum pressure) (the lower edge of the upper beam and the lower edge of the welding network sensor circle are flush) 3. The distance between the sensing head round surface of the two sensors and the upper beam plate is 1-2 mm. 4. Adjust the position of two sensors according to the above requirements, and the welding machine will start working. In production, if the fault shut down, will not use the problem, should contact the manufacturer in time, so as not to cause greater parts. damage
Related News
  • Key Points in the Use of Rebar Cutting Machine

    Key Points in the Use of Rebar Cutting Machine

    March 26, 2019Now the rebar cutting machine on the market has been improved through a few years, now the equipment that we can see has been more fully functional. In addition, the performance and quality of the mac...view
  • Precautions for Safe Using the Rebar Bending Machine

    Precautions for Safe Using the Rebar Bending Machine

    October 31, 20181. The rebar bending machine must have product specifications, certificates of conformity and maintenance records, it should be installed on a stable ground, and its cable insulation is good. Zero pro...view
  • Components of A Rebar Bending Machine

    Components of A Rebar Bending Machine

    October 13, 2018Rebar bending machine is one of the steel processing machinery. The working mechanism is a horizontal working disk that rotates on the vertical axis, and we should place the steel bar in the position ...view
  • Precautions for Operating the Standard Wire Bending Machine

    Precautions for Operating the Standard Wire Bending Machine

    November 27, 20181. The section which from 200mm to 250mm is checked on the metal wire and the surface of the wire must not be damaged when straightening.2. There are four vertical holes on the main pulling rod. The h...view
  • Truss Girder Welding Machine

    Truss Girder Welding Machine

    May 13, 2019Truss Girder Welding Machine SummaryMore and more building structures are used in the structure of the steel truss, especially the special type steel frame used in the stadium, exhibition hall and oth...view
  • Structural Features and Key Points of Large Truss Girder Welding Machine

    Structural Features and Key Points of Large Truss Girder Welding Machine

    May 7, 20191. Structural characteristics and main technical requirementsThe lower interrogation platform is the largest active part connected to the main tower. It is mainly composed of hinge seat, main truss, t...view
  • TEL:+86 22-26907986
  • FAX:+86 22-26997888
  • EMAIL:tjksales@tjkmachinery.com
  • ADDRESS:Wuwei Rd., Lulugang Logistics Industrial Park, Tianjin, China
online